* Fix filesystem mutex handling
This fixes the re-initialization of the filesystem mutex when the dyn storage
module is reinitialized. Using xSemaphoreCreateMutex would cause a memory leak
when the begin function is called multiple times and a semaphore leakage could
be caused by the re-initialization of the global fsMutex variable while the
semaphore is taken.
The fsMutex should not be taken while the logLine function is called as this
would cause a nested take of the fsMutex, which causes a deadlock.
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Fix hard coded littlefs in json upload
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Add new AP hardware support OpenEPaperLink_ESP32-PoE-ISO_AP
This is based on Olimex ESP32-PoE-ISO
https://www.olimex.com/Products/IoT/ESP32/ESP32-POE-ISO/open-source-hardware
It has a SD Card slot that is used to store all filesystem data on SD.
Use the prepare_sdcard.sh script to copy all needed data to an empty
SD card that is formatted with FAT filesystem. The AP firmware will format
the SD if an unformatted or from formatted card is used. This can be used
to intially prepare an empty SD card for usage.
For tag communication a ESP32-C6-WROOM-1(U) is used with the following
connection scheme:
ESP32-PoE-ISO | ESP32-C6-WROOM-1
---------------+------------------
GPIO5 | EN
GPIO13 | GPIO9
GPIO36 | GPIO3
GPIO4 | GPIO2
GPIO33 | GPIO24
GPIO32 | GPIO25
| GPIO8 pullup 5.1k
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Avoid error message log print when parsers.json is missing
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Workaround for IEEE802.15.4 modem stuck issue
The ESP32-C6 esp-idf based modem firmware can run into a case where it
does not receive data anymore from the tags. This can be detected when
it starts to print
"receive buffer full, drop the current frame"
and does not recover from that. In such a case a modem reset is triggered.
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Add OpenEPaperLink_ESP32-PoE-ISO_AP to release build
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Add OpenEPaperLink_ESP32-PoE-ISO_AP to condidional build
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
* Add Ethernet support
The ethernet support allows to make the network/internet connection
via LAN cable instead of WiFi. LAN is preferred, if a LAN cable is
connected and a valid IP configuration via DHCP can be obtained, WiFi
is switched off. If the LAN cable is disconnected, a fall back to
WiFi is done.
Use those defines in platform.ini for PHY settings:
ETHERNET_PHY_POWER: IO pin where the PHY can be switched of/on, can be
-1 if not used.
ETHERNET_CLK_MODE: PHY clock mode, see eth_clock_mode_t in ETH.h
ETHERNET_PHY_MDC: PHY MDC pin
ETHERNET_PHY_MDIO: PHY MDIO pin
ETHERNET_PHY_TYPE: PHY type, see eth_phy_type_t in ETH.h
Limitations:
- only DHCP is supported, no static IP configuration for LAN so far.
- If GPIO0 is used for one of the ETHERNET_CLK_MODE modes, then GPIO0
cannot be used to clear the WiFi configuration.
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
---------
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
Co-authored-by: Frank Kunz <mailinglists@kunz-im-inter.net>
1. Only call esp_ieee802154_receive_handle_done() when ack != NULL.
2. Add 2 millisecond timeout for all SubGhz MISO wait loops to
prevent watchdog timeouts when/if bad things happen (none observed
during testing)
3. Make CC1101 detection more robust and less intrusive by testing
MISO and CSn before trying to read chip version number.
4. Remove useless "error" messages which occur during normal operation.
5. Added missing \r in some log messages for EOL consistency.
* add support for lilygo t-panel
add support for lilygo t-panel (the rs485 version with an ESP32-S3 and ESP32-G2)
https://www.lilygo.cc/products/t-panel-s3
* refactor
* moved gfx library to lib2 folder and removed examples
* removed lib2\Arduino_GFX-1.3.7 and switch to moononournation/GFX Library for Arduino@^1.4.9
* added lilygo lib2\Arduino_GFX-1.3.7 back and removed all unused files. went from 166 files to 15 files!
* Added subGhz fixed channel support to tag config, added line accidentally dropped in pr7 merge.
* C6 - Fixed CRC error detection, added xtal frequency error
correction support. The xtal on commercial tags is assumed
to be better than those on crapy CC1101 modules.
* SubGhz radio fixes.
1. Don't for sending of BLOCK_MAX_PARTS parts for subGhz.
2. Fix CC1101 module detection logic.
3. Mitigate for lost CC1101 interrupts.
* Enabled SubGhz for OpenEPaperLink_Mini_AP_v4.
