Added support for Elcrow Advanced 2.8" AP.

ESP32_AP-Flasher/include/espflasher.h

@@ -7,6 +7,10 @@
    #define ESP_CHIP_TYPE   ESP32H2_CHIP
 #elif defined HAS_TSLR
    #define SHORT_CHIP_NAME "TSLR"
+#elif defined HAS_ELECROW_C6
+   #define SHORT_CHIP_NAME "ELECROW_C6"
+   #define OTA_BIN_DIR     "ESP32-C6"
+   #define ESP_CHIP_TYPE   ESP32C6_CHIP
 #elif defined C6_OTA_FLASHING
    #define SHORT_CHIP_NAME "C6"
    #define OTA_BIN_DIR     "ESP32-C6"

ESP32_AP-Flasher/platformio.ini

@@ -205,6 +205,7 @@ build_flags =
 	-D FLASHER_DEBUG_PROG=33
 	-D FLASHER_LED=-1
 	-D TFT_HEIGHT=480
+	-D TFT_HW_TYPE=226
 	-D USE_HSPI_PORT
 	-D LOAD_FONT2
 	-D MD5_ENABLED=1
@@ -269,6 +270,7 @@ build_flags =
 ; In this case we only got one TX Pin and no RX so lets only use that.
 	-D UART_LOGGING_TX_ONLY_PIN=43
 	-D TFT_HEIGHT=480
+	-D TFT_HW_TYPE=226
 	-D USE_HSPI_PORT
 	-D LOAD_FONT2
 	-D MD5_ENABLED=1
@@ -756,6 +758,74 @@ board_build.psram_type=qspi_opi
 board_upload.maximum_size = 16777216
 board_upload.maximum_ram_size = 327680
 board_upload.flash_size = 16MB
+
+; ----------------------------------------------------------------------------------------
+; !!! this configuration expects an ESP32-S3 16MB Flash 8MB RAM
+; ----------------------------------------------------------------------------------------
+[env:ESP32_S3_16_8_ELECROW_ADV_2_8]
+board = esp32-s3-devkitc-1
+board_build.partitions = large_spiffs_16MB.csv
+build_unflags =
+	-std=gnu++11
+    -D ARDUINO_USB_MODE=1
+    -D CONFIG_MBEDTLS_INTERNAL_MEM_ALLOC=y
+    -D ILI9341_DRIVER
+lib_deps =
+    ${env.lib_deps}
+build_flags = 
+	-std=gnu++17
+	${env.build_flags}
+	-D HAS_TFT
+	-D HAS_ELECROW_ADV_2_8
+	-D HAS_ELECROW_C6
+	-D CORE_DEBUG_LEVEL=0
+	-D ARDUINO_USB_MODE=0
+	-D CONFIG_ESP32S3_SPIRAM_SUPPORT=1
+	-D CONFIG_SPIRAM_USE_MALLOC=1
+	-D POWER_NO_SOFT_POWER
+	-D BOARD_HAS_PSRAM
+	-D CONFIG_MBEDTLS_EXTERNAL_MEM_ALLOC=y
+	-D HAS_BLE_WRITER
+	-D FLASHER_AP_SS=-1
+	-D FLASHER_AP_CLK=-1
+	-D FLASHER_AP_MOSI=-1
+	-D FLASHER_AP_MISO=-1
+	-D FLASHER_AP_RESET=46
+	-D FLASHER_AP_POWER={-1}
+	-D FLASHER_AP_TEST=-1
+	-D FLASHER_AP_TXD=9
+	-D FLASHER_AP_RXD=10
+	-D FLASHER_DEBUG_TXD=2
+	-D FLASHER_DEBUG_RXD=1
+	-D FLASHER_DEBUG_PROG=3
+	-D FLASHER_LED=-1
+	-D ST7789_DRIVER
+	-D TFT_WIDTH=240
+	-D TFT_HEIGHT=320
+	-D TFT_HW_TYPE=229
+	-D TFT_MISO=-1
+	-D TFT_MOSI=39
+	-D TFT_SCLK=42
+	-D TFT_CS=40
+	-D TFT_DC=41
+	-D TFT_RST=-1
+	-D TFT_RGB_ORDER=TFT_BGR
+	-D USE_HSPI_PORT
+	-D LOAD_FONT2
+	-D MD5_ENABLED=1
+	-D SERIAL_FLASHER_INTERFACE_UART=1
+	-D SERIAL_FLASHER_BOOT_HOLD_TIME_MS=50
+	-D SERIAL_FLASHER_RESET_HOLD_TIME_MS=100
+	-D C6_OTA_FLASHING
+build_src_filter = 
+	+<*>-<usbflasher.cpp>-<swd.cpp>-<webflasher.cpp>
+board_build.flash_mode=qio
+board_build.arduino.memory_type = qio_opi
+board_build.psram_type=qspi_opi
+board_upload.maximum_size = 16777216
+board_upload.maximum_ram_size = 327680
+board_upload.flash_size = 16MB
+
 ; ----------------------------------------------------------------------------------------
 ; !!! this configuration expects an SONOFF ZB Bridge-P
 ; ----------------------------------------------------------------------------------------

ESP32_AP-Flasher/src/ips_display.cpp

@@ -12,7 +12,12 @@
 #include "ips_display.h"
 
 #define YELLOW_SENSE 8  // sense AP hardware
+
+#ifdef HAS_ELECROW_ADV_2_8
+#define TFT_BACKLIGHT 38
+#else
 #define TFT_BACKLIGHT 14
+#endif
 
 TFT_eSPI tft2 = TFT_eSPI();
 uint8_t YellowSense = 0;
@@ -400,7 +405,9 @@ void sendAvail(uint8_t wakeupReason) {
     memcpy(&eadr.src, mac, 6);
     eadr.adr.lastPacketRSSI = WiFi.RSSI();
     eadr.adr.currentChannel = config.channel;
-#if defined HAS_LILYGO_TPANEL || defined HAS_4inch_TPANEL
+#ifdef TFT_HW_TYPE
+    eadr.adr.hwType = TFT_HW_TYPE;
+#elif defined HAS_LILYGO_TPANEL || defined HAS_4inch_TPANEL
     eadr.adr.hwType = 0xE2;
 #else
     eadr.adr.hwType = (tft2.width() == 160 ? 0xE1 : 0xE0);
@@ -435,10 +442,14 @@ void yellow_ap_display_init(void) {
     gfx->begin();
     gfx->fillScreen(BLACK);
 
+#else
+#ifdef HAS_ELECROW_C6
+    YellowSense = 0;
 #else
     pinMode(YELLOW_SENSE, INPUT_PULLDOWN);
     vTaskDelay(100 / portTICK_PERIOD_MS);
     if (digitalRead(YELLOW_SENSE) == HIGH) YellowSense = 1;
+#endif
     pinMode(TFT_BACKLIGHT, OUTPUT);
     digitalWrite(TFT_BACKLIGHT, LOW);