starred/OpenEPaperLink
1
0
Fork 0
mirror of https://github.com/OpenEPaperLink/OpenEPaperLink.git synced 2026-03-21 00:04:28 +01:00
Code Issues 472 Packages Projects Releases 10 Wiki Activity
Page: 2.9″ TG‐GM29MT1C ST‐GM29MTF
Pages
1.3” EL013H2WRD Peghook 1.54″ HS‐154R‐N 13.3″ EL133C2WRN 2.1″ Chroma‐21 2.2″ BWRY EL022F6W4A 2.2″ EL022H3WRA 2.6″ BWRY Newton Pro EL026F6W4A 2.7″ ST‐GR27000 2.9″ Chroma 29 2.9″ EL029D2WRA SubGHz 2.9″ EL029GSWRN 2.9″ EL029H3WRA 2.9″ ST‐GM29MT1 2.9″ TG‐GM29MT1C ST‐GM29MTF 4.2″ Chroma 42 4.2″ ST‐GR42 4.2″ TG‐GR42 4inch AP 7.4″ ST GM7500N 7.5″ ST‐GR750BN 88MZ100 Changelog 88MZ100 Programming and interfacing Access point pinouts Adding an SD card BLE only AP Beginners Guide for an easy to build Access Point (aka spaghetti AP) Binary file nomenclature Build AP firmware CC1310 Based Chroma Tags Chroma 74 Chroma 74H Chroma Aeon 74 Chroma Series SubGhz Tags Content cards Default settings for new Tags ESP32‐PoE‐ISO_AP Firmware Updates Flashing SiLabs based M3 Newton Displays Generic CC1101 modules for SubGhz Google Apps Scripts Home ICS calendar Installing SubGhz Beta Led control LilyGo T‐Panel AP Lithium Ion replacement for CR2450 M2 NFC 2.9″ and 1.54″ M2 Tag Firmware changelog M3 Tag Firmware changelog Nano AP V2 Opticon 2.1″ BWRY EE‐214RY Opticon 2.9″ BWRY EE‐293RY Opticon 4.2″ BWR EE‐420R Opticon 7.5″ BWR EE‐750R Opticon CC2533‐based tags Picture Frame for 7.4" Price tags RF protocol Restoring Lost Serial Numbers in Chroma Tags SubGhz AP Configuration SubGhz support for the LilyGo T‐Panel Tag protocol timing Troubleshooting usage Uploading & Using Custom Fonts, with examples Using your own fork with OTA updates Yellow AP with EByte CC1101 module rf‐wake tagtype notes
Clone
2.9″ TG‐GM29MT1C ST‐GM29MTF
Shuanglei Tao edited this page 2026-02-22 13:15:57 +08:00
Table of Contents

Specs

  • TI CC2630 ARM Cortex-M3 core, 128KB flash, 8KB SRAM, 20KB Ultra Low-Leakage SRAM, 24MHZ clock*, 802.15.4 2.4Ghz radio
  • 2.9” ePaper display (UC8151 or SSD1680)
  • SPI EEPROM (1M, W25Q80)
  • Dedicated wake-IC
  • NXP NFC controller (I2C)
  • 2x CR2450 Coin cell

Tag Information Note
Model TG-GM29MT1C
Options NFC
FCC ID None

ST-GM29MTF uses the same PCB as TG-GM29MT1C, but without the LED and NFC chip (not soldered).

Photos

1 2

SoC and Debug pinouts

CC2630

To program or read-out this tag you have two options:

  • Connect BL pin to GND and power on (or reset if already powered on) to enter bootloader mode, then use cc2538-bsl to flash firmware via UART.
  • cJTAG or JTAG programmer (J-Link or TI's XDS110), you need to solder the debug pins from the SOC, which is pretty hard for most people.

Firmware

https://github.com/tsl0922/Tag_FW_CC26xx